|
|
Список всех(!) кодов ошибок и их описание для принтеров HP LaserJet
Errors HP LaserJet all series and models(descriptions)
10.00.00 Supplies Memory Error alternates with 10.10.00 - ошибка картриджа (возможно перезаправлен или неоригинальный)
The printer is unable to read the electronic info on the print cartridge Replace print cartridge
13.XX Paper Jam - замятие бумаги
Media is jammed at the specified location (and possibly at other locations). If the message persists after all jams have been cleared, a sensor or sensor lever might be stuck or broken. For all jam messages, do the following:
1. Remove jammed print media from the specified location. Check the entire paper path for other pieces of media in the path.
2. Open and close the top cover to clear the message.
3. Check sensors and flags in the paper path for proper operation.
13.0 Paper Jam
A non-specific paper jam occurred.
1. Remove jammed media from the specified location.
2. Verify the paper tray is fully closed.
3. Inspect and/or replace the feed and separation rollers.
4. Ensure there is no obstruction in the path, such as a torn piece of paper.
5. Open and close the top cover to clear the message.
6. Check sensors and flags for proper operation.
13.1 Paper Jam Open Input Trays - замятие внутри лотка
Paper-delay jam at paper-feed area.
1. Ensure that paper trays are loaded and adjusted properly so media can feed from the tray. It might be necessary to reduce the stack height of media in the tray.
2. Check the input area for obstructions such as media in the path. Also check to see if the registration assembly damaged or unseated.
3. Replace any defective sensors or flags.
4. Verify the media meets the specifications.
5. Check the pickup feed and separation rollers for unusual wear. Replace as needed.
6. Rotate the media in the input tray by 180 and/or turn it over.
13.2 Paper Jam Open Input Trays
Paper-stopped jam at paper-feed area.
1. Check the input area for obstructions such as paper in the path. Also check to see if the registration assembly is damaged or if the transfer roller is out of place.
2. Replace any defective sensors or flags.
3. Ensure the media does not exceed the maximum length.
4. If multiple sheets are feeding, it might be necessary to fan the media and reduce the stack height. Also, replace separation pad.
5. Verify that the fuser is properly installed.
13.10 Paper Jam Check Duplexer Jam at duplexer.
1. Check the duplexer and the rear area of the printer for obstructions or damage.
2. Check the duplexer for proper operation. Replace the duplexer if a sensor is defective.
13.14
For Laserjet 5si. This error is caused by a defective paper control PCA Replace paper control PCA.
13.20 Paper Jam Check Rear Door
Media stopped in the paper path during power on or when the top door was closed.
1. Remove all media in the paper path, and then open and close the top cover.
2. If the message persists after all media is removed: Check if media is jammed in the prefeed area. Replace any defective sensors or flags
13.21 Door Open Jam
The top cover was open while printing.
1. Clear the jam and close the top door.
2. If the message persists, check the top door switch for proper operation.
13.5 Paper Jam Check Rear Door
Paper-delay jam at fuser.
1. Check the transfer roller and small media belt to ensure they are operating and can feed print media.
2. Check the paper path for obstructions at the transfer roller, toner cartridge, paper feed assembly, and fuser.
3. Replace any defective sensors or flags.
4. Turn the media stack over and/ or rotate it by 180 in the input tray.
13.6 Paper Jam Check Rear Door
Paper-stopped jam at fuser.
1. Check the paper path for obstructions at the fuser and output/delivery area.
2. Replace any defective sensors or flags.
13.99 Paper Jam
A non-specific paper jam occurred.
1. Remove jammed media from the specified location.
2. Verify the paper tray is fully closed.
3. Inspect and/or replace the feed and separation rollers.
4. Ensure there is no obstruction in the path, such as a torn piece of paper.
5. Open and close the top cover to clear the message.
6. Check sensors and flags for proper operation.
20 Insufficient Memory - недостаточно памяти (много отправили на печать?)
The printer received more data than can fit in available memory. You might have tried to transfer too many macros, soft fonts, or complex graphics. Press GO to print the transferred data (some data might be lost). Advise the customer to simplify the print job or install additional memory
21 Page too Complex - сложная печать
The data (dense text, rules, raster or vector graphics) sent to the printer is too complex Press GO to print the transferred data. (Some data might be lost.) Advise the customer to simplify the print job.
40 EIO x Bad Transmission - ошибка связи между принтером и устройством в слоте EIO (как правило это принт-сервер)
The connection has been broken between the printer and the EIO card in the specified slot. (Data loss might occur in this situation.)
1. Press GO to clear the error message and continue printing.
2. Reseat the EIO card in slot [X].
41.3 Unexpected Paper Size - неверный формат бумаги
The printer detected a media size different from what it was expecting. This is typically caused if two or more sheets stick together in the printer or if the tray is not properly adjusted.
1. Reload the tray with the correct print media size.
2. Ensure that media in the tray is loaded under the front and back tabs.
3. If you are printing from tray 1, verify that the correct paper size is selected in the control panel.
4. If you are printing from tray 2, 3, or 4, verify that the three paper-size adjustments (length guide, width guide, size-selector switch) on the paper tray have been made correctly. Make sure the media is under the corner tabs.
5. After performing the actions above, press GO. The page containing the error will automatically be reprinted if jam recovery is enabled. (Or, you might want to press CANCEL JOB to clear the job from the printers memory.)
41.5 Printer Error - проблема с прохождением бумаги (проверьте свою бумагу)
The media reached the PS102 or PS103 sensor too early.
1. This error usually occurs with smooth media, such as transparencies or labels. If the problem persists when using tray 1, load media one sheet at a time. If the problem persists when using trays 3 and 4, replace the feed and separation rollers.
2. Check sensors PS102 and PS103 for proper operation.
41.X Printer Error - ошибка принтера (передерните провода в принтере)
A temporary printing error has occurred. The page containing the error will automatically be reprinted. If the error persists:
1. Reseat the connections to the laser scanner and then to the engine controller board.
2. Replace the laser scanner.
3. Replace the engine controller board.
49.XX Printer Error (почитайте на форуме на этот счет)
A firmware error occurred
1. Press CANCEL JOB to clear the print job from the printer memory.
2. Turn the printer off, and then turn the printer on. Try printing a job from a different software application. If the job prints, go back to the first application and try printing a different file. (If the message only appears with a certain software application or print job, contact the software vendor for assistance.)
3. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or printer.
4. Turn the printer off.
5. Remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM in the lowest DIMM slot.)
6. Remove all EIO devices from the printer.
7. Turn the printer on.
8. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device.
9. Replace a DIMM or EIO device if you determine that it causes the error.
10. Remember to reconnect all cables that connect the printer to the network or computer.
11. If the error persists, replace the firmware DIMM.
12. Replace the formatter.
50.4 Printer Error - проблема с питанием (электрическая сеть)
A problem exists with the customers line voltage.
1. Remove the printer from any UPS supplies, additional power supplies, or power strips.
2. Plug the printer into a wall outlet and see if this resolves the problem.
3. If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used.
4. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications.
50.X Printer Error - ошибка узла закрепления
A fuser error has occurred.
1. Turn the printer off, wait 10 minutes, and then turn the printer on.
2. If the message persists, reseat the fuser. If that does not work, replace the fuser. To check the fuser, turn the printer off and remove the fuser. Measure the resistance between the fuser connectors. If it is not within the proper range, replace the fuser. If there is not continuity between the fuser connectors neutral and hot with the fuser removed, replace the fuser. If the problem is not related to the fuser, replace the engine controller board.
51.X Printer Error - ошибка лазера / сканера
A loss of beam-detect occurred. X description: 1 = Beam-detect error 2 = Laser error
1. Press GO. The page containing the error will automatically be reprinted.
2. Turn the printer off and then on.
3. Reseat cables to the laser/ scanner and engine controller.
4. Replace the laser/scanner.
5. Replace the DC controller.
52.X Printer Error - ошибка сканера
The laser scanner speed is incorrect. X description: 1 = Scanner startup error 2 = Scanner rotation error
1. Press GO. The page containing the error will automatically be reprinted.
2. Turn the printer off and then on.
3. Reseat cables to the laser/ scanner and engine controller.
4. Replace the laser/scanner.
53.XY.ZZ Printer Error - ошибка памяти (смотрите подкод!)
There is a memory error with an accessory. The DIMM that caused the error will not be used. Values of X, Y, and ZZ are as follows:
X = DIMM type 0 = ROM 1 = RAM
Y = Device location 0 = internal memory (ROM or RAM) 1 to 4 = DIMM slots 1, 2, 3, or 4
ZZ = Error number 0, 1, 2 = Unsupported o unrecognized memory 3 = Failed RAM test 4, 5 = Exceeded maximum RAM or ROM size 6 = Invalid DIMM speed 7 = DIMM reporting information incorrectly 8 = DIMM RAM parity error 9 = ROM needs to be mapped to an unsupported address 10 = DIMM address conflict 11 = PDC XROM out of bounds
12 = Unable to make a temporary mapping
1. Turn the printer off, and reseat or replace the specified DIMM.
2. Try the DIMM in another slot. (The firmware DIMM must remain in slot #4-the lowest DIMM slot.)
3. Replace the DIMM that caused the error.
54.1 Remove Sealing Tape - не выдернута чека в картридже
The toner cartridge has been installed without removing the sealing tape.
1. Open the top cover and remove the toner cartridge.
2. Pull the sealing tape tab to remove the strip.
3. Reinstall the toner cartridge and close the top cover.
54.2 Printer Error - проблема с каруселью
Indicates a problem exists with the carousel assembly. Either the carousel is not rotating or the sensor has failed.
1. Turn printer off then on to reset printer.
2. Open the color toner door and look for an obstruction. If necessary, remove the toner cartridges individually by manually releasing the carousel brake and rotating the carousel around to each cartridge
54.4 Printer Error alternates with Cycle Power to Continue - проблема с напряжением в электрической сети
A problem exists with the customers line voltage.
1. Remove the printer from any UPS supplies, additional power supplies, or power strips.
2. Plug the printer into a wall outlet and see if this resolves the problem.
3. If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used.
4. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications.
55.xx Printer Error alternates with Cycle Power to Continue - внутренняя ошибка (может быть - форматтер,память,плата питания)
An internal communications error occurred. The page containing the error will automatically be reprinted.
1. Check the power at the customers location.
2. Replace the formatter and/or firmware DIMM.
3. Replace the engine controller board.
4. Replace the formatter board.
56.X Printer Error - ошибка сортера
An incompatible combination of input/ output bins was selected.
X = description: 1 = Illegal input or bad accessory connector 2 - Illegal output The page containing the error will automatically be reprinted.
1. Turn the printer off, and then turn the printer on.
2. Check the printers configuration.
3. Verify accessory connection.
57.X Printer Error - ошибка вентилятора
A fan failure was detected.
X description: 1 = Printer fan 2 = Exhaust fan 3 = Drum drawer fan 7 = Duplex fan
1. Check the fans connector and make sure the fan is not blocked.
2. Replace the fan.
58.2 Printer Error - ошибка термистора
An environmental thermistor (TH3) failure occurred.
1. Turn the printer off, and then turn the printer on.
2. Verify the environmental thermistor cable is securely connected.
3. Replace the environmental thermistor.
4. If the error persists, replace the engine controller board.
59.X Printer Error - ошибка главного мотора
A main motor error occurred.
X description: 0 = Motor error 1 = Motor startup error 2 = Motor rotation error
1. Turn the printer off, and then turn the printer on.
2. Check and reseat the fuser and toner cartridge to make sure they are not hindering gear movement in the drive train.
3. Check the main motors cable to ensure that it is seated properly.
4. If the error persists, replace the main motor.
60.2 Printer Error - ошибка для кассеты 2(мотор лифта не работает)
The tray 2 lifter-motor is not functioning
1.Turn the printer off and then on.
2. If the error persists, turn the printer off
3. Verify that the tray 2 lifter wire-harness is full seated in its connector on the DC controller PCA (location J93)
4. Replace the tray 2 lifter-driver assembly
5. Replace the DC controller PCA
60.3 Printer Error - ошибка для кассеты 3(мотор лифта не работает)
Tray 3 lifter-motor failure
1.Turn the printer off and then on.
2. If the error persists, turn the printer off
3. Verify that the tray 3 lifter wire harness is fully seated in its connector on the sheet feeder PCA.
4. Replace the tray 3 lifter-driver assembly
5. Replace the DC controller PCA
60.4 Printer Error - ошибка для кассеты 4 (мотор лифта не работает)
Tray 4 lifter motor failure.
1.Turn the printer off and then on.
2. If the error persists, turn the printer off
3. Verify that the tray 4 lifter wire harness is fully seated in its connector on the sheet feeder PCA.
4. Replace the tray 4 lifter-driver assembly
5. Replace the DC controller PCA
62.X Printer Error - проблема с памятью (смотрите подкод!)
There is a problem with the printer memory. The X value refers to the location of the problem:
0 = Internal memory 1 to 4 = DIMM slots 1, 2, 3, or 4
1. Reseat the specified DIMM.
2. Replace the specified DIMM
64 Printer Error alternates with Cycle Power - ошибка буфера (может потребоваться Cold Reset!)
A scan buffer error occurred
1. Turn the printer off, and then turn the printer on.
2. Perform a cold reset.
3. If the message persists, replace the formatter or firmware DIMM.
66.XX.YY Failure - проблема с внешним устройством подачи бумаги
An error occurred in an external paper-handling device.
1st X = Device number in chain
2nd X = Device type 1 Input 2 Output 3 Stapler/stacker unit YY = Device specific error Press GO to clear the message. If the message will not clear:
1. Turn the printer off, and then turn the printer on.
2. Check and reseat all cables between the printer and the specified device.
3. Reseat the external paperhandling device.
4. Replace the unit.
68 NVRAM Error - ошибка памяти NVRAM (может потребоваться Cold Reset!)
Check Settings An error occurred in the printer non-volatile memory (NVRAM) and one or more printer settings has been reset to its factory default
1. Print a configuration page and check the printer settings to determine which values have changed.
2. Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used.
3. Replace the formatter.
68 NVRAM Full Check Settings - ошибка памяти NVRAM (может потребоваться Cold Reset!)
An error occurred in the printers NVRAM and one or more printer settings has been reset to its factory default.
1. Print a configuration page and check the printer settings to determine which values have changed.
2. Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used.
68.X Permanent Storage Error alternates with Check Settings - проблема с хранением данных (проверьте установки!)
An error occurred in the printers permanent storage and one or more printer settings has been reset to its factory default. Print a configuration page and check the printer settings to determine which values have changed.
68.X Permanent Storage Full проблема с хранением данных (переполнение-может потребоваться Cold Reset!)
The printers permanent storage is full. Some settings might have been reset to the factory defaults.
1. Print a configuration page and check the printer settings to determine which values have changed.
2. Hold down CANCEL JOB while turning the printer on. This will clean up the permanent storage by removing old areas that are not being used.
69.X Printer Error alternates with Cycle Power to Continue - ошибка дуплекса (смотрите подкод)
A temporary printing error occurred. X description: 0 = The duplex mechanism has failed
1. Turn the printer off, and then turn the printer on.
2. Reseat the duplexer.
3. Replace the duplexer.
79 Service - прервите печать и постарайтесь распечатать из другой программы
The printer detected an error.
1. Press CANCEL JOB to clear the print job from the printer memory.
2. Turn the printer off, and then turn the printer on.
3. Try printing a job from a different software application. If the job prints, go back to the first application and try printing again.
79 & 80 Error (проверьте свой принт-сервер!)
For trouble shooting 79 and 80 errors you want to determine if external I/O devices are the cause or if it is the formatter. Remove all external I/O devices (JetDirect, memory, etc.) and see if problem persists. If not, replace the formatter.
8X.YYYY EIO Error (проверьте свой принт-сервер!)
The EIO accessory in slot has encountered a critical error. description:
1 = EIO slot 1-The printer detected an error with the EIO accessory.
2 = EIO slot 2-The printer detected an error with the EIO accessory. 6 = EIO slot 1-The EIO accessory detected an error The EIO card may be defective
1. Turn the printer off, and then turn the printer on.
2. Turn the printer off, reseat the EIO accessory in slot , and then turn the printer on.
3. Turn the printer off, remove the EIO accessory from slot , install it in a different EIO slot, and turn the printer on
4. Replace EIO accessory in slot
Что-то все равно не понятно?Есть вопросы?Присылайте,мы поможем!
 
|